There are three basic causes of the vast majority of cyclecomputer malfunctions: Battery problems, wiring problems, and misalignment between the magnet and the sensor.
Press and hold the MODE and START/STOP buttons for 2 sec. in either the Elapsed Time, Trip Distance 1, Average Speed or Maximum Speed functions to reset these functions. The Odometer and Trip Distance 2 are not reset.
Resetting dataTo reset measurement data, display any data other than for Dst-2 and then press and hold MODE. Pressing and holding MODE with Dst-2 displayed resets Dst-2 only. The total distance is never reset.
- 1 Clear all data (initialization) Press the AC button on the back of the computer.
- 2 Select the speed units. Select “km/h” or “mph”.
- 3 Enter the tire circumference. Enter the front wheel tire circumference of your bicycle in mm.
- 4 Set the clock.
- 2 3.
- 60 cm.
- 5 mm.
- 2 Install the sensor and magnet.
Press the AC button on the back of the computer. * All data is deleted and the computer is reset to its factory default settings. 2 Select the measurement unit. Select “km/h” or “mph”.
- 1 Mount the bracket. • When mounting on stem.
- 70 cm. (27”)
- 2 Mount the speed sensor.
- 3 Mount the magnet. Speed sensor.
- 5 mm.
- 5 Attach/detach computer.
- 6 Test operation. After attaching the computer, rotate the front wheel gently to check that current speed is displayed on the computer.
- 4 Adjust the speed sensor and the magnet.
So the answer, really, is that a cycling computer is the best option. But if you're looking to save some cash and keep device ownership to a minimum, a phone will do the job.
Another advantage of the wireless computer is that if you have more than one bike you only need a couple of extra sensors and the wireless computer can easily be swapped from one bike to another. They are just as reliable, just as easy or easier to set up, and look better on the bike.
Wireless Speed allows a sensor to transmit the bicycles speed without a cable to the computer. Some computers have sensors that mount to the rear wheel instead of the front, making them suitable for use with indoor trainers. Some cycling computers can display a power reading, usually in watts.
The Cateye Strada wired cycle computer connects to the crank arm and the rear wheel. Then you have cadence as well as speed and you can put the computer back on your handle bars. Short answer: Yes.
Best Bike Computers Buying Guide
- Bike computers track your wheel's speed using magnets and sensors on the bike wheel and frame.
- They measure speed and distance, while more sophisticated models also track cadence.
- Bike computers typically offer fewer features than a GPS unit, but are much cheaper.
The best GPS bike computers, in order
- Wahoo ELEMNT Bolt. Best GPS bike computer.
- Garmin Edge 520 Plus. Best Garmin bike computer for most riders.
- Lezyne Super GPS. Best cheap bike computer – great for more casual users.
- Garmin Edge 1030. Best Premium bike computer.
- Cateye Padrone Smart+
- Lezyne Mega XL GPS.
- Polar Unisex V650.
A power meter is a device fitted to a bike that measures the power output of the rider. Strain gauges deflect slightly when a force is applied. By measuring this torque and combining it with angular velocity, power (measured in watts) can be calculated.
Generally, it is best to mount the magnet as close in toward the hub as possible. The closer in you mount it, the more slowly it will pass by the sensor, giving the sensor's magnetic switch more time to respond. If the magnet is too far out, the computer may give erratic readings at higher speeds.
Best Overall: Garmin Edge 830 Sensor BundleThis cycle computer sports a full-color touchscreen display that makes all its technological capabilities feel even more impressive. The Garmin Edge 830 stands apart from other bike computers on the market today because of its navigation features.
Bell Bike Computer Instructions
- Place one end of a measuring tape at the top edge of one of the bicycle's wheels.
- Press the button on the right side of the bike computer repeatedly to set the appropriate wheel factor.
- Press the right button to set the computer to display distances in kilometers or miles, as desired.
how do I remove my cateye padrone from the out-front bracket? Need to change battery and reset computer. Answer: Just slide it forward and it will come out.
- From the measurement screen, press MENU to switch to the menu screen. Measurement screen.
- Press MODE to display the screen shown below, and then press MODE for 2 seconds.
- Switch off the functions you want to skip by moving to the relevant icon and turning the setting off.
- Press MENU to confirm settings.
